manualshive.com logo in svg

HP 5800, Command Reference Manual

Share
Download
HP 5800 Command Reference Manual Download Page 135

 

126 

 Blockade Multiplier: 4 

 Graceful Restart: ENABLE 

 Restart Time: 200 sec       Recovery Time: 150 sec 

Table 49

 

Command output 

Field Description 

LSR ID 

Label switched Router ID, in the format of X.X.X.X 

Resv Confirmation Request 

Reserved confirmation request 

RSVP Hello Extension 

State of the hello mechanism: enabled or disabled 

Hello Interval 

Hello interval, in seconds 

Max Hello misses 

Maximum number of consecutive hello losses before 
a neighbor is considered dead 

Path and Resv message refresh interval 

Path and reservation message refresh interval, in 
seconds 

Path and Resv message refresh retries count 

Number of Path and Resv message retransmissions 

Blockade Multiplier 

Blockade multiplier 

Graceful Restart 

State of GR: enabled or disabled 

Restart Time 

GR restart interval in seconds 

Recovery Time 

GR recovery interval in seconds 

 

# Display the RSVP-TE configuration on interface VLAN-interface 3.  

<Sysname> display mpls rsvp-te interface ethernet 1/1 

Interface Vlan-interface3 

 Interface state: UP       BFD feature: ENABLE 

 Total-BW: 80              Used-BW: 20 

 Hello configured: NO      Num of Neighbors: 1 

 SRefresh feature: ENABLE  SRefresh Interval: 30sec 

 Authentication: DISABLE   Reliability configured: NO 

 Retransmit Interval: 500msec  Increment Value: 1 

Table 50

 

Command output 

Field Description 

Interface  

RSVP-TE enabled interface 

Interface state 

Physical interface state 

BFD feature 

State of BFD: enabled or disabled. 

Total-BW 

Total bandwidth (in kbps). 

Used-BW 

Used bandwidth (in kbps). 

Hello configured 

State of the hello mechanism: enabled or disabled. 

Num of Neighbors 

Number of neighbors connected to the interface.  

Srefresh feature 

State of the summary refresh function: enabled or disabled. 

Srefresh interval 

Summary refresh interval (in seconds). 

Summary of Contents for 5800













































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands