HP 5800 Command Reference Manual Download Page 246

Page: 246 / 396

237

View

Any view

Default level

1: Monitor level

Parameters

all

: Displays all L2VPN information.

group

group-name

: Specifies the name of the peer group, which is a string of 1 to 47 characters.

ip-address

: Specifies the IP address of the peer.

verbose

: Displays detailed information.

route-distinguisher

route-distinguisher

: Specifies the route distinguisher in the format of nn:nn or IP-

address:nn. It can be a string of 3 to 21 characters.

ce-id

ce-id

: Specifies the CE ID of the VPN connected with the MPLS L2VPN connection. A remote

connection requires the remote CE ID. The value range of the CE ID is from 0 to 199.

label-offset

label-offset

: Specifies the label offset, which ranges from 0 to 65,535.

: Filters command output by specifying a regular expression. For more information about regular

expressions, see the

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, which is a case-sensitive string of 1 to 256 characters.

Examples

# Display all information about L2VPN in the BGP routing table.

<Sysname> display bgp l2vpn all

BGP Local router ID : 2.2.2.9, local AS number : 100

Origin codes:i - IGP, e - EGP, ? - incomplete

bgp.l2vpn: 1 destination

Route Distinguisher: 100:1

CE ID Label Offset Label Base nexthop pref as-path

1 0 8202 3.3.3.9 100

Table 89

Command output

Field Description

Origin codes

Route origin codes, which can be:
i – IGP—Indicates that the network layer reachability

information is from within the AS
e – EGP—Indicates that the network layer
reachability information is learned through EGP
? – incomplete—Indicates that the network layer
reachability information is learned through other

ways

bgp.l2vpn

Number of BGP L2VPNs

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands

HP 5800, Command Reference Manual

Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands