HP 5800 Command Reference Manual Download Page 365

Page: 365 / 396

356

Syntax

display bgp vpnv6 vpn-instance

vpn-instance-name

routing-table

[

network-address prefix-length

[

longer-

prefixes

] |

peer

ipv6-address

{

advertised-routes

received-routes

} ] [

{

begin

exclude

include

}

regular-expression

]

View

Any view

Default level

1: Monitor level

Parameters

vpn-instance-name

: Specifies the VPN instance name, which is a case-sensitive string of 1 to 31

characters.

network-address

: Specifies the IPv6 address of the destination network segment.

prefix-length

: Specifies the length of the prefix, ranging from 0 to 128.

longer-prefixes

: Displays each routing entry that meets the following conditions:

•

Its destination IPv6 address ANDed with the specified prefix equals the specified destination IPv6
address ANDed with the specified prefix.

•

Its prefix length is shorter than or equal to the specified prefix length.

•

Its prefix length is the longest among the entries meeting the above two conditions.

peer

ipv6-address

: Displays the routing information sent to or received from the specified BGP VPNv6

peer.

ipv6-address

is the IPv6 address of the peer.

advertised-routes

: Displays the routing information sent to the specified peer.

received-routes

: Displays the routing information received from the specified peer.

: Filters command output by specifying a regular expression. For more information about regular

expressions, see the

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, which is a case-sensitive string of 1 to 256 characters.

Examples

# Display the BGP VPNv6 routing information of VPN instance

vpn1

<Sysname> display bgp vpnv6 vpn-instance vpn1 routing-table

BGP Local router ID is 1.1.1.1

Status codes: * - valid, ^ - VPN best, > - best, d - damped,

h - history, i - internal, s - suppressed, S - Stale

Origin : i - IGP, e - EGP, ? - incomplete

Total routes of vpn-instance vpn1: 1

*^> Network : 324:: PrefixLen : 64

NextHop : 100::2 LocPrf : 100

PrefVal : 0 Label : NULL

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands

HP 5800, Command Reference Manual

Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands