Home
/
HP
/
5800
/
Command Reference Manual

HP 5800, Command Reference Manual

Share

Page: 189 / 396

HP 5800 Command Reference Manual Download Page 189

180

Use the

undo mpls te link administrative group

command to restore the default.

The default link administrative group attribute is 0x00000000.
The interface properties are propagated globally. They are used for path selection at the tunnel ingress.
Related commands:

mpls te affinity property

.

Syntax

mpls te link administrative group

value

undo mpls te link administrative group

View

Interface view

Default level

2: System level

Parameters

value

: Specifies the link administrative group attribute, ranging from 0x00000000 to 0xFFFFFFFF. It is a

set of 32 link properties. Each bit represents a property with a value of 0 or 1. By ANDing the

administrative group attribute bits with the link affinity attribute bits of an MPLS TE tunnel, MPLS TE

identifies the properties of the links that the MPLS TE tunnel can use.

Examples

# Assign VLAN-interface 1 the link administrative group attribute of 0x00000101.

<Sysname> system-view

[Sysname] interface vlan-interface 1

[Sysname-Vlan-interface1] mpls te link administrative group 101

mpls te loop-detection

Description

Use the

mpls te loop-detection

command to configure the node to perform loop detection when setting up

the MPLS TE tunnel.
Use the

undo mpls te loop-detection

command to disable loop detection.

Loop detection is disabled by default.

Syntax

mpls te loop-detection
undo mpls te loop-detection

View

Tunnel interface view

Default level

2: System level

Parameters

None

«
...
187
188
189
190
191
...
»

Summary of Contents for 5800













































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands