HP 5800 Command Reference Manual Download Page 306

Page: 306 / 396

297

Field Description

Flag

Flag of the route. Possible values are:

•

U—available route

•

G—gateway route

•

H—host route

•

B—blackhole route

•

D—dynamic route

•

S—static route

OutInterface Forwarding

interface

Token

LSP index number

display fib vpn-instance

ip-address

Description

Use the

display fib

vpn-instance

ip-address

command to display the FIB information of the specified VPN

instance that matches the specified destination IP address.
If you do not specify either the

mask

or the

mask-length

parameter, the command displays the FIB

information of the specified VPN instance that matches the specified destination IP address and has the

longest mask. Otherwise, the command displays the FIB information of the specified VPN instance that

exactly matches the specified destination IP address and mask.

Syntax

display

fib vpn-instance

vpn-instance-name ip-address

[

mask | mask-length

] [

{

begin

exclude

include

}

regular-expression

]

View

Any view

Default level

1: Monitor level

Parameters

vpn-instance-name

: Specifies the name of the VPN instance, which is a case-sensitive string of 1 to 31

characters.

ip-address

: Specifies the destination IP address, in dotted decimal format.

mask

: Specifies the mask of the IP address, in dotted decimal format.

mask-length

: Specifies the length of the IP address mask, ranging from 0 to 32.

: Filters command output by specifying a regular expression. For more information about regular

expressions, see the

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, which is a case-sensitive string of 1 to 256 characters.

Summary of Contents for 5800













































































































































































































































































































































































































Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands

HP 5800, Command Reference Manual

Search results

Summary of Contents for 5800

Reviews:

Brands by name

Popular brands