horsch Focus 4 TD Operating Instructions Manual Download Page 98

Page: 98 / 108

11 | Optional equipment

60059040 • 02 • 07/2021 • en

11.11.2 Parking brake

DANGER

Serious accidents from loss of stability!

Park the machine only on a level and firm ground.

Secure the machine against rolling away before unhitching.

Parking brake crank

Always apply the parking brake and secure the machine against rolling away
before parking the machine.

Release the parking brake before parking for a longer period of time or after
the end of the season. Brake pads may otherwise stick to the drum and make
restarting of the machine more difficult.

Always release the parking brake before transport travels. The cables must be
relieved, and the wheels must be free to rotate.

Maintenance

Check the function of the parking brake before connecting the machine.

Where necessary adjust the cable or the brake pads.

Summary of Contents for Focus 4 TD













































































































Search results

Summary of Contents for Focus 4 TD

Reviews:

horsch Focus 4 TD, Operating Instructions Manual, Page: 98 / 108

Search results

Summary of Contents for Focus 4 TD

Reviews: