manualshive.com logo in svg

horsch Focus 4 TD, Operating Instructions Manual, Page: 68 / 108

Share
Download
horsch Focus 4 TD Operating Instructions Manual Download Page 68

7 | Operation

68

60059040 • 02 • 07/2021 • en

Pneumatic system –
Metering unit

Ø

Has the correct rotor been installed?

Ø

Have the sealing lips been adjusted and are they still serviceable?

Ø

In case of small seed, has the cleaning brush been installed and is it in order?

Ø

In the case of large seed, has the scraper been installed?

Ø

Are all connections airtight and has the discharge flap been closed firmly and
leak free?

Ø

Does seed flow out of all coulters?

Ø

Is seed bridging forming in the hopper, especially with husky seed?

Ø

Is the correct seed quantity being placed, especially in the case of small seed?

7.5 Depth setting

7.5.1 Depth of fertiliser placement

In the field the depth guidance of the machine is accomplished by the packer and
the support wheels.

The working depth of the tines and thus the depth of the fertiliser placement is set
by the height of the machine.

Ø

Adjust the depth at the rear with clips on the packer cylinders and at the front
on the arms of the support wheels. The ratio of aluminium clips to working
depth is approx. 1:3. If a clip of 1 cm thickness is removed, this corresponds to
approx. 3 cm working depth, depending on soil conditions.

Ø

Align the tine frame parallel to the ground. Insert the required number of alu-
minium clips on the front support wheels for this purpose. For machines with
swinging drawbar hitching clips must also be applied to the piston rods of the
hydraulic cylinders on the articulated drawbar. With tractor link arm hitching,
the height of the two-point on the tractor must be corrected, if necessary.

NOTE

The fertiliser placement depends on the conditions in the field and
can therefore only be adjusted during use.

Ø

Check the placement when starting work and regularly during use.

7.5.2 Depth of the levelling discs

WARNING

Dropping or lowering machine parts can cause severe crushing injuries etc.!

Ø

Instruct persons to leave the danger zone.

Ø

Comply with the accident prevention instructions.

Ø

The depth setting takes place by the folding hydraulics.

Ø

Switch the drill controls to 

Folding

 in the drill controls.

Ø

Set the control unit briefly to 

Folding in

, this extends the cylinders of the level-

ling discs.

Summary of Contents for Focus 4 TD













































































































Reviews:

No comments