horsch Focus 4 TD Operating Instructions Manual Download Page 38

Page: 38 / 108

5 | Attachment

60059040 • 02 • 07/2021 • en

Colour

blue

red

yellow

black

Silver

Thickness

7 mm [0.28

″

] 10 mm

[0.39

″

]

19 mm
[0.75

″

]

30 mm
[1.18

″

]

50 mm
[1.97

″

]

WARNING

Risk of injury on the hydraulic cylinders!

Limbs may be pinched or crushed by unintentional retraction of the piston rods.

Park the machine to attach or remove the clips with the parking brake pulled.

Order persons to leave the area of the tractor cab.

Make sure when placing or removing clips that the control units are not oper-
ated by any other person.

Lock control units mechanically or electrically, depending on the version.

CAUTION

Danger of damage to the packer frame.

Depending on the design, do

not

remove any fixed clips or depth limitations!

NOTE

Pay attention to the ratio on the machine.

Summary of Contents for Focus 4 TD













































































































Search results

Summary of Contents for Focus 4 TD

Reviews:

horsch Focus 4 TD, Operating Instructions Manual, Page: 38 / 108

Search results

Summary of Contents for Focus 4 TD

Reviews: