horsch Focus 4 TD Operating Instructions Manual Download Page 64

Page: 64 / 108

7 | Operation

60059040 • 02 • 07/2021 • en

Apply the parking brake (optional) and secure the machine with wheel chocks
against rolling away.

Uncouple the machine.

Disconnect the lines between tractor and machine.

With swinging drawbar hitching close the lock valve on the drawbar.

7.3 Folding

WARNING

Serious crushing due to lowering / dropping machine parts

No persons may stay under raised machine parts.

Order persons to leave the danger zone around the machine. Make sure be-
fore folding that no persons are present in the danger zone.

Comply with the accident prevention instructions.

WARNING

Risk of accident due to insufficient stability

Fold the machine only after it has been fully connected.

The machine must not be in an inclined position when folding it.

Fold the machine only on a level and firm surface.

CAUTION

Damages to the machine

Before folding in clean the area around the folding joints and the associated
hydraulic cylinders.

7.3.1 Unfolding

Perform folding operations only on level, firm ground.

Lift the machine completely.

Select

Folding

in the drill controls and operate the control unit.

Unfold the machine, until the pressure gauge shows min. 80 bar. The step on
the hopper is automatically extended.

Switch the control unit to neutral position.

Slightly lift the machine to be able to remove aluminium clips from the packer
cylinder.

In case of swinging drawbar hitching remove the clips from the drawbar cylin-
der.

Summary of Contents for Focus 4 TD













































































































Search results

Summary of Contents for Focus 4 TD

Reviews:

horsch Focus 4 TD, Operating Instructions Manual, Page: 64 / 108

Search results

Summary of Contents for Focus 4 TD

Reviews: