XNX Universal Transmitter
Section 5 - Warnings/Faults
113
5.2 Fault Messages
Fault
Description
Appli-
cable
Sensors
Latching / Non-
Latching
Frequency of
Diagnostic
Event History Data
Action For Resolution
F101
Unexpected Sen-
sor Reset
All
Non-latching
ECC & mV: main
loop x2;
Optima & Excel: 2
seconds
Note 2� Optima or
Excel: Sensor fault or
warning code (Note 4)
If repeated, check supply voltage, check cable loop impedance, check
terminal connections
F103
XNX Temperature
Error
All
Non-latching
2 seconds
XNX temperature
(Celsius)
Check location for heat sources� Fit with sunshade or other protec-
tion� Change the transmitter’s location� Check temperature in Info-
>Transmitter Status to ensure temperature is being measured properly�
F104
XNX 24 VDC Sup-
ply Bad
All
Non-latching
2 seconds
XNX supply voltage
x1000
Check the wire of the 24V power supply to the transmitter and the power
supply operation�
F105
3�3VDC Supply
Bad on XNX, per-
sonality board, or
option board
All
Non-latching
2 seconds
1=XNX,
2=Personality board,
3=Option board
Check Transmitter Status
F106
XNX Real Time
Clock Failure
All
Non-latching
2 seconds
Total seconds since
Jan 1, 1970
Either clock was incorrectly set or the battery for the clock has failed�
Note: the clock will stop running on January 1, 2036�
F107
XNX Internal Fail-
ure (RAM, ROM,
EEPROM, Opcode)
All
Non-latching ex-
cept for EEPROM
error
At power up and
8 hours
Note 3
Contact Honeywell Analytics’ Service Department�
F108
XNX mA Output
Loop Failure
All
Latching
2 seconds
mA output error (mea-
sured mA - set mA)
Check wiring of mA output from XNX� Check that switches S1 and S2 are
set correctly� Note that if F108 is not resolved quickly, an F149 (Internal
Communication Failure - mA) will also be generated� When the cause of
F108 is resolved, both the F108 and F149 will be cleared�
F109
Simulated Warn-
ing/Fault
All
Non-latching
Enabled by user
0
Performing an alarm/fault reset will clear all simulation�
F110
Sensor software
mismatch
Optima
Latching
Only checked at
power up
Sensor firmware ver-
sion x10
Contact Honeywell Analytics’ Service Department�
F111
Negative Drift
ECC, mV
Non-latching
2 seconds
Raw gas concentra-
tion of sensor
Check sensor location for external interference� Perform zero calibra-
tion� If problem persists after zero calibration and no interference exists,
replace sensor�
Negative Drift; may
indicate a failed IR
sensor
Optima,
Excel
Non-latching
XNX polls sensor
every 2 seconds,
diagnostic fre-
quency controlled
by sensor
Sensor fault or warn-
ing code
Check sensor location for external interference� Perform zero calibra-
tion� If problem persists after zero calibration and no interference exists,
replace sensor�
Summary of Contents for XNX
