XNX Universal Transmitter
Section 6 - Specifications
154
6.4.4 Multi Purpose Detector (MPD)
Similar to the XNX Transmitter, the MPD part numbering system defines the agency approval and thread type� The only material selection
is Stainless Steel� Four sensor selections are available� Agency Approvals are specific to the 4 sensor types� Ensure the approval of
the specific sensor type meets the requirements of the installation�
Model Type
Port Config
Installed Sensor
Range
(See Section 6.2 for Agency Approvals)
MPD
-
q
q
q
q
q
AM
M25
CB
- Catalytic Bead %LEL
1
- Default
UT
3/4” NPT
IF
- IR %LEL Flammable
2 to 9
- Future
BT
3/4” NPT
IV
- IR Methane 0-5% Vol
IC
- R Carbon Dioxide 0-5% Vol
6.4.5 XNX Catalytic Bead and IR Replacement Sensor Cartridges
Sensor
Type
1, 2
Target Gas
Cartridge
Part No
Operating
Pressure
Range
(kPa)
Operating
Humidity
Range (%
RH non-
condensing)
Air
Speed
(m/s)
Maximum
Range
Selectable
Range
3
Increment
Default
Range
Cal Gas Range
Cal Gas P/N
Cal Gas
Description
MPD-IC1
Carbon Dioxide
1226-0301
80 - 110 see footnote 4
0 - 6
5.00 %Vol
1.00 to 5.00 %Vol
1.00 %Vol
5.00 %Vol
1.50 to 3.5 %Vol
Contact HA
2.5 %VOL CO
2
in Air
MPD-IV1
Methane
1226-0299
80 - 110
0 - 95
0 - 6
5.00 %Vol
1.00 to 5.00 %Vol
1.00 %Vol
5.00 %Vol
1.50 to 3.5 %Vol
GFV352
2.5 %VOL CH
4
in Air
Methane
1226-0299
80 - 110
0 - 95
0 - 6
100 %LEL
1.00 to 5.00 %Vol
1.00 %Vol
5.00 %Vol
1.50 to 3.5 %Vol
GFV352
2.5 %VOL CH
4
in Air
MPD-IF1
Flammables
1226-0300
80 - 110
0 - 95
0 - 6
100 %LEL
20 to 100 %LEL
3
10 %LEL
100 %LEL
30 to 70 %LEL
GFV406
1 %VOL C
3
H
8
in Air
MPD-CB1 Flammables
1226A0359
80 - 120 see footnote 5
0 - 6
100 %LEL
20 to 100 %LEL
3
10 %LEL
100 %LEL
30 to 70 %LEL
GFV352
50 %LEL CH
4
in Air
1. Agency approved hydrogen sensors are MPD-CB1 and 705 STD.
2.
When ordering replacement MPD sensor cartridges, the replacement cartridge must be the same type as factory configured. Substituting a different cartridge
will void agency certification.
3.
On XNX %LEL units carrying UL/CSA certifications, the range is fixed at 100%LEL and is not adjustable.
4. Humidity: 5% to 95% RH non-condensing
5. Humidity: 0 to 99% RH non-condensing
Summary of Contents for XNX
