6
≤ 350 mm
≤ 260 mm
3.
1.
≤ 380 mm
2.
19
30 Nm
A
B/C
32 mm
51 mm
33 mm
A
B
C
26027
S105 - 10/2014
© 2014 Honeywell International Inc.
Honeywell Fall Protection Deutschland GmbH & Co. KG * Seligenweg 10 * D-95028 Hof
+49 (0) 9281 83 02 0 *
+49 (0) 9281 36 26 * [email protected] * www.honeywellsafety.com
INSTALLATION SPECIFICATIONS
Fig. 2c
≤ 350 mm
≤ 260 mm
3.
1.
≤ 380 mm
2.
19
30 Nm
A
B/C
32 mm
51 mm
33 mm
A
B
C
26027
S105 - 10/2014
© 2014 Honeywell International Inc.
Honeywell Fall Protection Deutschland GmbH & Co. KG * Seligenweg 10 * D-95028 Hof
+49 (0) 9281 83 02 0 *
+49 (0) 9281 36 26 * [email protected] * www.honeywellsafety.com
1.26 in.
1.3 in.
2 in.
15 in.
13.8 in.
10.2 in.
Fig. 2a
≤ 350 mm
≤ 260 mm
3.
1.
≤ 380 mm
2.
19
30 Nm
A
B/C
32 mm
51 mm
33 mm
A
B
C
26027
S105 - 10/2014
© 2014 Honeywell International Inc.
Honeywell Fall Protection Deutschland GmbH & Co. KG * Seligenweg 10 * D-95028 Hof
+49 (0) 9281 83 02 0 *
+49 (0) 9281 36 26 * [email protected] * www.honeywellsafety.com
≤ 350 mm
≤ 260 mm
3.
1.
≤ 380 mm
2.
19
30 Nm
A
B/C
32 mm
51 mm
33 mm
A
B
C
26027
S105 - 10/2014
© 2014 Honeywell International Inc.
Honeywell Fall Protection Deutschland GmbH & Co. KG * Seligenweg 10 * D-95028 Hof
+49 (0) 9281 83 02 0 *
+49 (0) 9281 36 26 * [email protected] * www.honeywellsafety.com
≤ 350 mm
≤ 260 mm
3.
1.
≤ 380 mm
2.
19
30 Nm
A
B/C
32 mm
51 mm
33 mm
A
B
C
26027
S105 - 10/2014
© 2014 Honeywell International Inc.
Honeywell Fall Protection Deutschland GmbH & Co. KG * Seligenweg 10 * D-95028 Hof
+49 (0) 9281 83 02 0 *
+49 (0) 9281 36 26 * [email protected] * www.honeywellsafety.com
Fig. 2b
22 ft.-lbs.
≤ 350 mm
≤ 260 mm
3.
1.
≤ 380 mm
2.
19
30 Nm
A
B/C
32 mm
51 mm
33 mm
A
B
C
26027
S105 - 10/2014
© 2014 Honeywell International Inc.
Honeywell Fall Protection Deutschland GmbH & Co. KG * Seligenweg 10 * D-95028 Hof
+49 (0) 9281 83 02 0 *
+49 (0) 9281 36 26 * [email protected] * www.honeywellsafety.com
5.2 Installation of End Stop at Bottom
of Rail System
ENd STOP 26027
note: the 26027 end stop is designed for installation
at the bottom and at the top of the rail system. Follow
all installation specifications and instructions for
proper mounting.
1. Fix the end stop to the back of the bottom guide
rail section, aligning, ordering and assembling the
components of the end stop as shown (see Fig. 2a)
to the oblong hole in the guide rail (see Installation
Specifications for location of end stop in relation to
bottom and top of rail system).
2. Using a 19mm bolt torque wrench, tighten the nut to 22
ft.-lbs. (30Nm) (see Fig. 2b).
3. Install the red plunger to the end of the shaft using a
rubber mallet (see Fig. 2c).
WARNING:
In order to prevent incorrect insertion
of the fall arrester to the guide rail, it must only
be inserted after the bottom end stop has been
installed.
IMPORTANT:
If the ladder is not mounted at
ground level, a second bottom end stop must be
installed (see Fig. 2e). The second bottom end stop
should be located approximately 5 ft. (1.5m) from
the bottom of the rail. This will ensure maximum
safety for a worker when descending.
