Honeywell DCS19W Installation And User Manual Download Page 39

Page: 39 / 84

Failure Modes

One Razzberry Tone

This indicates that the scanner has experienced a laser subsystem failure. The scanner will try up to three

times to correct the failure condition. If the laser subsystem continues to fail, that subsystem (horizontal or

vertical) will be shut down and an error indication will be shown on the Diagnostic Indicator Display. This error

stays on the display until corrected. If the remaining subsystem is still operational, scanning will continue using

the operational components.

Two Razzberry Tones

This indicates that the scanner has experienced a motor subsystem failure. The scanner will try up to three

times to correct the failure condition. If the motor subsystem continues to fail, that subsystem (horizontal or

vertical) will be shut down and an error indication will be shown on the Diagnostic Indicator Display. This error

stays on the display until corrected. If the remaining subsystem is still operational, scanning will continue using

the still operational components.

Continuous Razzberry Tone with Blue LED Off

If, upon power up, the scanner emits a continuous razzberry tone, then the scanner has an electronic failure.

Return the unit for repair at an authorized service center.

Three Beeps - On Power Up

If the scanner beeps three times on power up then, the nonvolatile memory that holds the scanner

configuration has failed. Return the unit for repair at an authorized service center.

Summary of Contents for DCS19W





















































































Search results

Summary of Contents for DCS19W

Reviews:

Related manuals for DCS19W

Brands by name

Popular brands

Honeywell DCS19W, Installation And User Manual

Search results

Summary of Contents for DCS19W

Reviews:

Related manuals for DCS19W

Brands by name

Popular brands