Honeywell DCS19W Installation And User Manual Download Page 50

Page: 50 / 84

Scale Calibration Procedure (lbs. or kg) with Remote Display

1. Temporarily Remove the platter and place it in a safe location.

Note: It is the responsibility of the owner of the scale to confirm compliance with the relevant Weights

and Measures statutes and regulations applicable in your area by checking with the appropriate

government agency before placing a newly calibrated unit into service or removing any official

seals.

2. If this is a currently installed scanner/scale in need of calibration, cut and remove the calibration switch

cover seal. If this is a new installation, cut and remove the factory-applied adhesive seal.

Follow all Electro-Static Discharge (ESD) procedures when exposing internal scanner/scale

components.

3. Remove the M3 screw securing the calibration switch/button cover. Place the cover and screw in a safe

location. Verify that the scale calibration switch is in the Run position.

Figure 38. Calibration Switch/Button Cover Removal

Summary of Contents for DCS19W





















































































Search results

Summary of Contents for DCS19W

Reviews:

Related manuals for DCS19W

Brands by name

Popular brands

Honeywell DCS19W, Installation And User Manual

Search results

Summary of Contents for DCS19W

Reviews:

Related manuals for DCS19W

Brands by name

Popular brands