Honeywell DCS19W Installation And User Manual Download Page 51

Page: 51 / 84

Scale Calibration Procedure (lbs. or kg) with Remote Display

4. Enter full service access mode. Power down the unit if necessary. Press and hold down the Calibration

push button then power up the scanner/scale. Release the Calibration push button.

Figure 39. Entering Full Service Access Mode

See Power Source caution statement located on page 12 of this manual.

5. Enter calibration mode. The remote display will flash all of the characters available (see illustration below).

Press the right arrow button twice (►)(►) while the display flashes all characters. The remote display

should read CAL 1.

Figure 40. Enter Calibration Mode

6. Reinstall the platter onto the scanner/scale. Check the platter to ensure that it is seated properly and

nothing is interfering with its freedom to move.

Figure 41. Install Platter

Summary of Contents for DCS19W





















































































Search results

Summary of Contents for DCS19W

Reviews:

Related manuals for DCS19W

Brands by name

Popular brands

Honeywell DCS19W, Installation And User Manual

Search results

Summary of Contents for DCS19W

Reviews:

Related manuals for DCS19W

Brands by name

Popular brands