Honeywell DCS19W Installation And User Manual Download Page 46 | Manualshive

Page: 46 / 84

background image

42

Startup

When the scanner first receives power, the blue LED will turn on and the scanner will beep once. The scanner

is now ready to scan.

Power-Up Test Mode

When a MS2420 scanner is first powered up, it cycles through a number of self-tests before starting normal

operation. If there are any initial failures during this sequence of tests the scanner will beep or razz to indicate

the error and an error code will appear in the diagnostic indicator display.
The following are examples of the types of tests performed at power-up.
1.  Memory tests
2.  Hardware setup tests
3.  Motor tests
4.  Laser tests
5.  Configuration tests
6.  Interface tests
7.  Scale tests
These tests are also performed on a periodic basis with the operator alerted to any failures.

Configuration Mode

All MS2420 series scanners have been configured at the factory with a set of default communication protocols.

Since many host systems have unique formats and protocol requirements, A wide range of configurable

features that may be selected with the use of the MetroSelect Configuration Guide (PN 00-02407x), the

MS2xxx Stratos Series Configuration Addendum (PN 00-02034x) and MetroSet can be provided.

«
...
44
45
46
47
48
...
»

Summary of Contents for DCS19W





















































































Reviews:

No comments

Related manuals for DCS19W

Brand: Magtek Pages: 2

Brand: Cognex Pages: 29

Brand: Farpointe Data Pages: 2

Brand: Dormakaba Pages: 28

Brand: Atid Pages: 2

Brand: Atid Pages: 30

Brand: Atid Pages: 35

Brand: Vasco Pages: 178

Brand: Velleman Pages: 2

Brand: Velleman Pages: 32

ReadEasy Move 2

Brand: VisionAid International Pages: 25

SmartTouch Swipe

Brand: Embed Pages: 14

Brand: Nordic ID Pages: 12

Brand: Nordic ID Pages: 35

Brand: Interlogix Pages: 14

Brand: Pocketbook Pages: 98

Brand: RIOTEC Pages: 4

Brand: Manhattan Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands