Honeywell DCS19W Installation And User Manual Download Page 35

Page: 35 / 84

Wake Activation Area (Photocell LED Output)

The MS2420 scanner’s default power save mode

†

is Dual Action Power Save Mode #2 (see page ). This

power save mode turns the laser OFF after a configured period of non-use then turns the motor OFF after

thirty-minute intervals. Any movement detected by the photocell in the activation area, shown below in grey,

will cause the scanner to exit the power save mode. The motor will restart automatically and the laser will turn

back on preparing the scanner for bar code recognition, decoding and transmission.

Figure 26. Wake Activation Area Perpendicular to Package Flow Default Range

(Photocell LED Output)

†

Refer to the MetroSelect Configuration Guide (PN 00-02407) for additional information on configurable

power save modes.

Specifications are subject to change without notice.

Summary of Contents for DCS19W





















































































Search results

Summary of Contents for DCS19W

Reviews:

Related manuals for DCS19W

Brands by name

Popular brands

Honeywell DCS19W, Installation And User Manual

Search results

Summary of Contents for DCS19W

Reviews:

Related manuals for DCS19W

Brands by name

Popular brands