Honeywell DCS19W Installation And User Manual Download Page 31

Page: 31 / 84

EAS Deactivation

SW1 and SW2 are the switch banks inside the Checkpoint device that set the deactivation range. The

following is a list of Checkpoint recommended switch bank settings.

Checkpoint Recommended Switch Bank Settings

SW1

SW2

Switch 1 and 6

Switch 2, 3, 4, and 5 OFF

All MS2420 models have a connector labeled EAS In on the bottom of the unit. An optional EAS cable

(PN 52-52511x or 52-52556x) available for purchase for connection between the Checkpoint device and the

scanner.

Figure 20. EAS Cable Connection (Bottom of MS2420)

The following figure shows the location of the EAS deactivation area for the MS2420 scanner. It is important to

pass the entire tag through this area to deactivate the security tag.

Figure 21. EAS Deactivation Area

Summary of Contents for DCS19W





















































































Search results

Summary of Contents for DCS19W

Reviews:

Related manuals for DCS19W

Brands by name

Popular brands

Honeywell DCS19W, Installation And User Manual

Search results

Summary of Contents for DCS19W

Reviews:

Related manuals for DCS19W

Brands by name

Popular brands