Honeywell DCS19W Installation And User Manual Download Page 12

Page: 12 / 84

Scale Capacities

Capacity: kg unit 15 kg

lb. unit 30.0 lb.

Minimum Increment: kg unit 0.005 kg

lb. unit 0.01 lb.

Maximum Static

Weight: kg unit 75 kg

lb. unit 150 lb.

Adjustments

required: Calibration is required for scaled units.

Electrical

Voltage Supply: 4A @ +5V / 0.8A @ +12V

Operating Power: 11.2 Watts

Standby Power: 4.0 Watts

Operating Current: 1.7A @ 5.2V / 0.2A @ 12V

Standby Current: 0.6 A @ 5.2V / 0.07A @ 12V

DC Transformers: Class I; 5.2VDC @ 4A; 12VDC @ 1.5A

For Regulatory Compliance Information, refer to pages 69 - 71.

Environmental

Operating

Temperature: 0°C to 40°C (32°F to 104°F)

IP Rating: IP 55

Light Levels: 4842 Lux (450 footcandles)

Storage

Temperature: -40°C to 60°C (-40°F to 140°F)

Humidity: 5% to 95% Relative Humidity, Non-Condensing

Contaminants: Sealed to resist airborne particulate contaminants.

Ventilation: None Required

Specifications are subject to change without notice.

Summary of Contents for DCS19W





















































































Search results

Summary of Contents for DCS19W

Reviews:

Related manuals for DCS19W

Brands by name

Popular brands

Honeywell DCS19W, Installation And User Manual

Search results

Summary of Contents for DCS19W

Reviews:

Related manuals for DCS19W

Brands by name

Popular brands