FINAL DRIVE
12-9
FINAL DRIVE DISASSEMBLY/
INSPECTION
BACKLASH INSPECTION
Before inspecting the backlash, modify the special
tool at four places as shown. Be sure the modified
areas on the plate fit properly around the stud bolts.
Set the final drive assembly in a vise.
Install suitable washers onto the stud bolts of the
filler hole side.
Install the special tools onto the gear case and into
the pinion joint to hold it.
Remove the oil filler cap.
Set a horizontal type dial indicator on the ring gear
through the oil filler hole.
Turn the ring gear back and forth to read the
backlash.
Remove the dial indicator. Turn the ring gear 120
°
and measure the backlash. Repeat this procedure
once more.
Compare the difference of the three measurements.
If the difference between the three measurements
exceeds the service limit, it indicates that the bear-
ing is not installed squarely, or the case is
deformed.
Inspect the bearings and case.
If the backlash is excessive, replace the right ring
gear shim with a thicker one.
If the backlash is too small, replace the right ring
gear shim with a thinner one.
• Fifteen different shim thicknesses (from A to P)
are available in increments of 0.06 mm (0.002 in).
Select the shim from A to I.
TOOL:
Holder plate
07924-9690103 or
07924-9690101
(modified)
10 mm
17 mm
7 mm
27 mm
27 mm
Circle
center
Ø14 mm (4 places)
TOOLS:
Pinon holder
07924-ME40010
Collar set “C”
07924-ME40020
Holder plate (modified)
07924-9690103 or
07924-9690101
(modified)
STANDARD: 0.05 – 0.15 mm (0.002 – 0.006 in)
SERVICE LIMIT: 0.30 mm (0.012 in)
SERVICE LIMIT: 0.10 mm (0.004 in)
DIAL INDICATOR
RING GEAR
Shims J to P may
be used only for the
left shim
(page 12-14).
Summary of Contents for GOLDWING GL1800
