background image

24 

5.10 Five point harness

The five point harness should be installed by authorized dealers or 

trained technicians.

Take the seat upholstery off first. Loosen all the carriage bolts of the 

hip pads. Pull out the seat plate completely to get easy access to the 

set of rectangular slots in the seat plate underneath the hook strap.

Choose one of them according to the desired seat depth and slot 

it with a cutter. The position should be close to the body but not 

underneath the bottom. Thread the strap from above through the 

slot and between seatplate and seat base to the rear edge of the 

seat plate. Place the thickened end of the strap right to this edge 

so that the strap is firmly secured after tightening the bolts.  Put the 

seat plate and the hip pads to the desired position and tighten the 

carriage bolts.

Put the seat upholstery back again and thread the other end of the 

strap through the slot in the seat upholstery.

To attach the strap to the buckle proceed as described in 5.8 lap 

belt.

Lead the shoulder straps together with the pad straps through the 

designated slots in the back insert

Fix the shoulder straps to the slots in the back base as described in 

5.8 lap belt

Tie the pad straps together.

The shoulder straps should be adjusted in a way that the housing of 

the length adjusters rest on the shoulder padding.

Summary of Contents for Bingo OT










































Reviews: