137
Optimisation / Minimisation des masses
Mode d’emploi
Optimisation/ Weight minimisation
Operation Manual
geodyna 6800-2/p
geodyna 6800-2/p
12.3 Démarrer optimisation de stabilité de
marche ou minimisation des masses
—
Bloquer correctement (voir § 6.5) la roue complète
pour effectuer la minimisation, ou la jante uniquement
pour lancer une optimisation.
—
En cas de MINIMISATION, contrôler que le pneu
soit correctement monté sur la jante (vérifi cation
d’excentricité) et qu’il soit gonflé à la pression
prescrite.
—
Sélectionner le type de véhicule (voir § 7.1.1).
—
Relever les dimensions de la jante (voir § 7).
—
Exécuter la lancée de mesure.
—
Sur l’écran EQUILIBRAGE, appuyer sur la touche de
menu
F1
, puis sélectionner l’option Optimisation
(1,
Fig. 12-1)
.
L’image OPTIMISATION (
Fig. 12-2
)
est alors affi chée.
Il est maintenant possible de lancer la procédure comme suit.
Lancer l’optimisation de stabilité de masses
—
Appuyer sur la touche de menu
F4
, puis sélectionner
l’option Lancer l’optimisation
(1, Fig. 12-2a)
.
L’image OPTIMISATION 1 (
Fig. 12-4
) est alors affi chée.
Continuer comme décrit au § 12.3.2.
Lancer la minimisation des masses
—
Appuyer sur la touche de menu
F4
puis sélectionner
l’option Lancer la minimisation
(1, Fig. 12-2b)
.
L’image MINIMISATION 1 (
Fig. 12-5
) est alors affi chée.
—
Continuer depuis l’option MINIMISATION 1 comme
décrit au § 12.3.1.
Récupération de l’optimisation/minimisation
Nota Bene
:
Si une optimisation/minimisation interrompue se
trouve en mémoire, l’écran OPTIMISATION
(Fig.
12-4)
s’affiche lorsque l’option Optimisation est
sélectionnée dans le menu F1.A l’aide de la touche
F3
, il est possible de reprendre le cycle interrompu à
partir de l’étape de programme en cours au moment
de l’interruption.
—
Bloquer la roue retirée auparavant avec l’interruption
de l’optimisation/minimisation.
—
Appuyer sur la touche de menu
F3
.
Il sera affiché celui des écrans au cours duquel
l’optimisation de la stabilité de marche / la minimisation
des masses a été interrompue auparavant.
—
Procéder selon l’étape de programme en cours.
minimisation
—
To perform a Minimisation run correctly clamp a
complete wheel (Section 6.5) or just the rim for an
Optimisation run.
—
For a MINIMISATION run, check that the tyre is
correctly mounted on the rim (Axial run-out test)
and that it is pumped up to the set pressure.
—
Select the Vehicle Type (Section 7.1.1).
—
Read the rim dimension parameters (Chapter 7).
—
Launch a Measuring run.
—
On the BALANCING screen press the
F1
Menu key,
and then select the Optimisation item
(1, Fig. 12-1)
.
The OPTIMISATION screen (
Fig. 12-2
) is displayed.
You can now start the procedure as follows.
Start weight optimisation
—
Press the
F4
Menu key and then select the Start
Optimisation item
(1, Fig. 12-2a)
.
The OPTIMSATION 1 screen (
Fig. 12-4
) is displayed.
Continue as described in Chapter 12.3.2.
Start weight minimisation
—
Press the
F4
Menu key and then select the Start
Minimisation item
(1, Fig. 12-2b)
.
The MINIMISATION 1 screen (
Fig. 12-5
) is displayed.
—
Proceed from the MINIMISATION 1 item as described
in Chapter 12.3.1.
Recalling Optimisation/ Minimisation
Note
:
If a previously interrupted Optimisation/Minimisation
run is in the memory, when the Optimisation item
is selected from the F1 Menu, the OPTIMISATION
screen
(Fig. 12-4)
is displayed.The interrupted cycle
can be restarted using the
F3
Menu key. The program
will proceed from exactly the point at which is was
interrupted.
—
Clamp the wheel removed previously when the
Optimisation/Minimisation run was interrupted.
—
Press the menu key
F3
.
The screen in which optimisation/weight minimisation
was previously interrupted is displayed.
—
Proceed according to the current programme stage.