HNP Mikrosysteme mzr-2521 Operating Manual Download Page 7

Page: 7 / 92

1 General information

Operating manual mzr-2521 and mzr-2921

Last update: June 2019

Technical data subject to change without prior notice!

General information

This operation manual contains basic instructions to be followed during

integration, operation and maintenance of the mzr

micro annular gear pump.

For this reason it is necessary to read it carefully before any handling of the

device. The present manual should always be kept at the operation site of the

micro annular gear pump.

In case assistance is needed, please indicate the pump type visible on the

housing.

1.1

Application scope of the pumps

The micro annular gear pumps mzr-2521 and mzr-2921 described in this manual

are suitable for continuous delivery and discrete dosage of water, watery

solutions, solvents, methanol, oils, lubricating liquids, paints and varnishes as well

as many other liquids.

If you intend to handle any aggressive, poisonous or radioactive liquids, you

must conform to safety measures as according to the regulations in force. Any

project concerning handling of corrosive liquids should be previously discussed

with the pump manufacturer.

The micro annular gear pumps should not be used for "invasive" medical

applications, in which the liquid having had contact with the pump is re-

introduced to the body.

The micro annular gear pumps are not to be used in motor vehicles, rail

vehicles, aircraft and spacecraft. (Approval of the manufacturer necessary!)

Exception: The micro annular gear pumps can be used in or on watercrafts.

The data concerning resistance of the pumps to manipulated liquids is

elaborated according to the best of HNP Mikrosysteme's knowledge. However,

operating parameters varying from one application case to another, no

warranty for this information can be given.

The information given in this manual does not release the customer from

personal obligation to check the integrity, correct choice and suitability of the

pump for the intended use. The use of the micro annular gear pumps should

be conform with technical norms and regulations in force.

If you wish to receive more information than comprised in this manual please

contact directly HNP Mikrosysteme.

1.2

Product information

The present operating manual is valid for the micro annular gear pump types

mzr-2521 and mzr-2921 manufactured by HNP Mikrosysteme GmbH,

Bleicherufer 25, 19053 Schwerin, Germany.

Summary of Contents for mzr-2521





























































































Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands

HNP Mikrosysteme mzr-2521, Operating Manual

Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands