HNP Mikrosysteme mzr-2521 Operating Manual Download Page 30

Page: 30 / 92

5 Optional modules

Operating manual mzr-2521 and mzr-2921

Technical data subject to change without prior notice!

Last update: June 2019

5.5

Stepper motor drive (optional)

The micro annular gear pump mzr-2521 and mzr-2921 can alternatively be driven

by a stepper motor. This motor is characterized not only by small dimensions but

also by a large speed range, which perfectly covers the operating speed range of

the pumps.

Stepper motor

Operation

Current mode

Motor type

AM1524 A 0.25

Speed range

1 --- 3000 rpm

Phase resistance (at 20°C)

12.5 k

Ω

Inductance per phase (1 kHz)

5.5 mH

Nominal current per phase (2 current phases) 0.25 A
Back -EMF amplitude

3.5 V/k steps/s

Holding torque (2 current phases)

6 mNm

Step angle (full step)

15°

Max. allowed winding temperature

130 °C

Thermal time constant

220 s

Operating temperature range

-40 … + 70 °C

Weight

12 g

table 12

Technical data of the stepper motor

figure 18

Measurements of the micro annular gear pump mzr-2521 and mzr-2921 with the stepper motor

The stepper motor can be operated with an adapted control unit. For this

purpose the motor should be connected with a ribbon cable to the solder joint of

the control unit.

Pin 4 phase B

Pin 3 phase B

Pin 2 phase A

Pin 1 phase A

figure 19

PCB of the round stepper motor version

Summary of Contents for mzr-2521





























































































Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands

HNP Mikrosysteme mzr-2521, Operating Manual

Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands