HNP Mikrosysteme mzr-2521 Operating Manual Download Page 48

Page: 48 / 92

6 System integration

Operating manual mzr-2521 and mzr-2921

Technical data subject to change without prior notice!

Last update: June 2019

6.8

Operation with the S-BL control unit (optional)

The micro annular gear pumps mzr-2521 and mzr-2921 with brushless DC motor

as drive be delivered with the S-BL control unit. This programmable control unit

enables to adjust speed for constant flow rates or the position of the motor for

the dosage of constant amounts of liquid. On the delivered diskettes or CDs you

will find a PC-program operating under Windows that enables to program such

parameters as speed, acceleration and current consumption. The delivery package

comprises also a null-modem cable for connection to a serial interface of a PC.

S-BL control unit

Type of control unit

4-Q servo amplifier

Nominal voltage

Power supply

12 - 30

Residual ripple

≤

2 %

Max. continuous output current

continuous

410*)

Max. peak output current

max

700*)

Speed range

10...6000*)

rpm

Input No. 1

input resistance

Ω

Nominal analog speed

voltage range

Nominal digital speed

PWM signal

low 0...0.5 / high 4...30

frequency range

100...2000

Input No. 2

open collector

max. U

/ 30 mA

no error

switched to GND

programmed as input

low 0...0.5 / high 3,5... U

Input No. 3

TTL - logic level

low 0...0.5 / high 3,5...30

PLC - logic level

low 0...7 / high 12,5...30

Program memory

6,6

kBytes

*) Values limited in the control unit with corresponding software

table 24

Technical data of the S-ND control unit

The control unit permits an easy startup of the pump with:

−

the possibility to connect the voltage supply to the delivered DIN socket

−

the possibility to connect the voltage supply with screw clamps

−

a 8-pole screw clamps connector assembly for the motor cable

−

speed set with potentiometer

−

analog voltage signal 0-10 V for speed control at the screw clamps

−

9-pole connection plug for the RS-232 interface

−

error output with status LED, programmable also as trigger input with screw

connections

−

tumbler switch S1 for the connection of digital input No. 3 of the motor

control unit

Summary of Contents for mzr-2521





























































































Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands

HNP Mikrosysteme mzr-2521, Operating Manual

Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands