HNP Mikrosysteme mzr-2521 Operating Manual Download Page 53

Page: 53 / 92

7 The startup/shutdown of a pump

Operating manual mzr-2521 and mzr-2921

Last update: June 2019

Technical data subject to change without prior notice!

Nature of the handled liquid

Flushing cycle
[min]

Suitable flushing liquid

Oils, fats, plastifiers

15-20

isopropanol, ethanol, acetone, benzine

Solvents (polar + nonpolar)

5-10

isopropanol, ethanol

Other organic liquids

10-15

isopropanol , ethanol

Refrigerating and cooling agents

15-20

isopropanol, ethanol

Neutral watery solutions

20-25

isopropanol, ethanol

Basic solutions

25-30

DI-water (deionized water)

Organic acids

30-40

isopropanol, ethanol

Weak mineral acids

25-30

DI- water

Strong mineral acids

35-45

DI- water

Strong oxidizing liquids

35-45

DI- water

Paints, varnishes, adhesives

50-60

Not specified - for further information
please contact HNP Mikrosysteme.

table 26

Selection of the flushing liquid (solvent) and the duration of the flushing cycle depending on the delivered liquid.

Warning

Please make sure that the pump components and particularly O-rings and

sealing are resistant to the employed flushing liquid (see table 27).

Shaft sealing

O-ring material

Flushing liquid

PTFE,

graphite-reinforced

UHMWPE

FPM

EPDM

FFPM

acetone

benzene

benzyl alcohol

benzine

butanol

dimethyl sulfoxide (DMSO)

ethanol

isopropanol

methanol

methylethylketone (MEK)

oil / fine mechanics oil

styrene

toluene

water

xylene

Legend:

0 ... good suitability 1 ... suitability 2 ... conditional suitability 3 ... labile - ... not specified

table 27

Resistance of the sealing materials depending on the flushing liquid (solvent)

Summary of Contents for mzr-2521





























































































Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands

HNP Mikrosysteme mzr-2521, Operating Manual

Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands