manualshive.com logo in svg

HNP Mikrosysteme mzr-2521, Operating Manual

Share
Download
HNP Mikrosysteme mzr-2521 Operating Manual Download Page 58

7  The startup/shutdown of a pump 

Operating manual mzr-2521 and mzr-2921 

52

 

Technical data subject to change without prior notice!

 

Last update: June 2019

 

7.5

 

Trouble shooting 

If the pump does not start to operate or stops the operation abruptly, please 

proceed as follows: 

Try to liberate the micro annular gear pump: 

−

 

by turning the potentiometer knob back and forth or by sending an analog 

voltage signal 

−

 

via the control software 

−

 

by pressing with a syringe a suitable flushing liquid (see table 26 and table 27) 

through the micro annular gear pump 

−

 

by changing the operating direction of the pump. 

If these measures turn out to be ineffective, please contact the service staff of 

HNP Mikrosysteme (see chapter 16) and send the pump back to the manufacturer 

for inspection. 

 Warning 

 

You should under no condition try to dismantle the pump by yourself. This 

may cause damage to the pump components and consequently annul your 

warranty claims. 

7.6

 

Return of the micro annular gear pump to the manufacturer 

For the return of a micro annular gear pump and components that have already 

been employed, please follow the instructions: 

−

 

drain any remaining rests of the delivered liquid from the pump 

−

 

flush the pump with an adapted solvent 

−

 

remove the filter elements from integrated or loosely delivered filters 

−

 

protect all openings against dust with the delivered protective plugs or screws  

−

 

return the pump in its original packing 

The service personnel which carries out the repair should be informed about the 

condition of the used micro annular gear pump. This is done by means of the 

"Declaration of media in contact with the micro annular gear pump and 

components" (see chapter 19). This form may also be downloaded from the web 

site 

https://www.hnp-mikrosysteme.de/service/download-center.html

. 

!

 

The "Declaration of media in contact with the micro annular gear pump and 

components" must imperatively be filled in. The nature of liquid which entered 

into contact with the micro annular gear pump and the components must be 

specified.  

In case of non-compliance, the sender will be liable for any resulting injure to 

persons or any object damage. 
 

Summary of Contents for mzr-2521





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands