HNP Mikrosysteme mzr-2521 Operating Manual Download Page 56

Page: 56 / 92

7 The startup/shutdown of a pump

Operating manual mzr-2521 and mzr-2921

Technical data subject to change without prior notice!

Last update: June 2019

7.4.1

Conservation

If the micro annular gear pump operates at irregular intervals or for other reasons

should be put out of operation for a longer period, it should, after service and

flushing procedure (see chapter 7.3), be filled in with a suitable conservation

liquid.

The conservation liquid may be selected from the table 28 depending on the

duration of the standstill and the resistance of the pump to the manipulated

liquid (table 27). The indicated conservation liquids are simple recommendations

and should therefore be checked by the user as to their compatibility and

suitability. The figure 32 presents the diagram of conservation liquid selection.

Remark

: This diagram is repeated as a part of the figure 31 »Shutdown

procedure«.

After the cleansing procedure the pump should be filled with a suitable

conservation agent. You will find a choice of possible conservation liquids in the

table 28.

Selection of conservation

liquid (CL)

adequate

Is the CL

compatible

w ith pump

Is the CL

compatible

w ith the

last FL ?

yes

figure 32

Selection of the conservation liquid (CL)

see table 27 (resistance of the sealing materials)

see table 28 (Selection of conservation liquid)

Summary of Contents for mzr-2521





























































































Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands

HNP Mikrosysteme mzr-2521, Operating Manual

Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands