HNP Mikrosysteme mzr-2521 Operating Manual Download Page 11

Page: 11 / 92

1 General information

Operating manual mzr-2521 and mzr-2921

Last update: June 2019

Technical data subject to change without prior notice!

1.5

Technical data of the micro annular gear pump mzr-2521 and mzr-2921

mzr-2521

mzr-2921

Technical data

Displacement volume

1.5 µl

3 µl

Housing length without fluid connections

69 mm

Housing length with fluid connections

−

slip fitting version Ø 2 mm

−

manifold assembly version

75 mm
71 mm

Diameter

13 mm

Weight

−

slip fitting version Ø 2 mm

−

manifold assembly version

56 g
65 g

Internal volume

65 µl

67 µl

Housing material

stainless steel
316L (1.4404),
epoxy resin adhesive

Fluid connector material

stainless steel 316L (1.4404)

Rotor material

tungsten carbide (WC-Ni)

Bearing material

tungsten carbide (WC-Ni) / ceramics

Dynamic sealing

graphite-reinforced PTFE, stainless steel spring 316L

Static sealing

FKM; optional EPDM, FFKM

Performance parameters

Min. flow rate Q (at 1 rpm)

0.0015 ml/min*

0.003 ml/min*

Max. flow rate Q (at 6000 rpm)

9 ml/min (= 0.54 l/h)

18 ml/min (= 1.08 l/h)

Min. dosage volume

0.25 µl

0.5 µl

Differential pressure (at viscosity 1 mPas)

1.5 bar

3 bar

Max. applied inlet pressure

1 bar

Viscosity

0.3 --- 100 mPas
(1000 mPas*)

Dosage precision CV

1 %

Operating temperature

-20 … 60 °C

Ambient temperature

-20 … 65 °C

Storage temperature

10 … 40 °C

Pulsation of flow (theoretical value)

1.5 %

6 %

NPSHR value

0.6 m

0,6 m

Legend:

* with supplementary modules

CV Coefficient of variation

NPSHR Net Positive Suction Head Required

table 1

Technical data and performance parameters of the micro annular gear pumps mzr-2521 and mzr-2921

Warning

The material property of a liquid (e.g. viscosity, lubricating property, particle

content, corrosiveness) impacts the technical data and the service life of

pumps.

At appropriate conditions the characteristic values may be increased or

decreased.

Warning

If you intend to operate the pump out of the range of the above given

specification, please consult the manufacturer. Modifications may be necessary

to ensure successful operation. Otherwise the pump or the system may be

damaged seriously.

Summary of Contents for mzr-2521





























































































Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands

HNP Mikrosysteme mzr-2521, Operating Manual

Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands