HNP Mikrosysteme mzr-2521 Operating Manual Download Page 49

Page: 49 / 92

6 System integration

Operating manual mzr-2521 and mzr-2921

Last update: June 2019

Technical data subject to change without prior notice!

Startup of the micro annular gear pump with the S-BL control unit

speed regulation

serial interface of PC

external voltage supply
24 V DC / 2.5 A

Status LED

mzr-pump

switch S1

figure 29

Connection of the micro annular gear pump mzr-2521 or mzr-2921 and the S-BL control unit

Connect the motor cable to the 6-pole connector of the S-BL control unit.

The pin configuration is indicated in table 14 and table 25.

Function

Connection

Color

Phase A

Ph A

brown

Phase B

Ph B

orange

Phase C

Ph C

yellow

Hall sensor A

Hall A

green

Hall sensor B

Hall B

blue

Hall sensor C

Hall C

grey

V5 V

Vcc

red

Ground

SGND

black

table 25

Pin configuration of the motor

Connect the RS-232 port of the MCBL3006 with a free serial interface of a

PC. For this purpose use the delivered 9-pole null-modem cable.

Put the potentiometer of the S-BL control unit to zero position by turning it

clockwise to the limit stop.

Connect the voltage supply 24 VDC. This can be done with the integrated

DIN connector or, alternatively the 2-pole screw clamp (24 V = »+«;

GND = »-«). Pay attention to the correct polarity.

You may now install the delivered software »Motion Manager« as described

in the chapter 9.

While connecting the DC voltage pay attention to the correct polarity,

otherwise electronics may be damaged.

Summary of Contents for mzr-2521





























































































Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands

HNP Mikrosysteme mzr-2521, Operating Manual

Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands