manualshive.com logo in svg

HNP Mikrosysteme mzr-2521, Operating Manual

Share
Download
HNP Mikrosysteme mzr-2521 Operating Manual Download Page 31

5  Optional modules 

Operating manual mzr-2521 and mzr-2921 

Last update: June 2019 

Technical data subject to change without prior notice!

 

25 

 

5.6

 

Brushless DC motor as drive (option) 

The micro annular gear pump mzr-2521 and mzr-2921 can alternatively be driven 

with a brushless DC-motor. It is characterized by higher dimensions and a wider 

speed range, which covers entirely the speed range of the micro annular gear 

pump and shows a longer service life than a brushed DC-motor. 

Performance parameters 

 

Nominal voltage 

24 V 

Max. continuous torque 

2.6 mNm 

Power 

11 W 

No-load speed at 9 V 

11,583 rpm 

Max. continuous current 

0.44 A 

Terminal resistance, phase-phase 

15.1 

Ω

 

Terminal inductance, phase-phase 

525 µH 

Speed range 

1 --- 6000 rpm 

Ambient temperature 

-30 … +125 °C 

Type of Hall effect sensor 

analog (  digital) 

analog hall sensors 

1000 pulse/rev. 

digital hall sensors 

3 pulse/rev. 

Legend: 

  Option for the S-KB control unit 

table 13 

Technical data of the brushless DC-motor 

Function 

Connection 

Color 

Phase A 

Ph A 

brown 

Phase B 

Ph B 

orange 

Phase C 

Ph C 

yellow 

Hall sensor A 

Hall A 

green 

Hall sensor B 

Hall B 

blue 

Hall sensor C 

Hall C 

grey 

V5 V 

Vcc 

red 

Ground 

SGND 

black 

table 14 

Pin configuration of the motor 

 

  

figure 20 

Measurements of the micro annular gear pump mzr-2521 or mzr-2921 with a brushless DC-motor 

Summary of Contents for mzr-2521





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands