HNP Mikrosysteme mzr-2521 Operating Manual Download Page 41

Page: 41 / 92

6 System integration

Operating manual mzr-2521 and mzr-2921

Last update: June 2019

Technical data subject to change without prior notice!

6.6

Operation with the S-KD control unit (optional)

The micro annular gear pumps mzr-2521 and mzr-2921 may optionally be

delivered with the S-KD control unit. The speed for constant flow rates may be

adjusted with a 4-Q servoamplifier. The delivery comprises also a PCB for

connection of the motor cable.

S-KD control unit

Nominal voltage

Power supply

12 - 30

Residual ripple

≤

3 %

Max. output current

max

230*)

Max. output power

max

Speed range

200...6000*)

rpm

Nominal value input »Set Value«

10 or

3.9 configurable

Status signal »Ready«

Open collector max. U

/ 20 mA

no error: »Ready« = high impedance
Ready »Ready« = GND

Connection of »Disable«

Measurements

approx. 114 x 100 x 34

Weight

approx. 370

Working temperature range

0 … +45

°C

*) Values limited in the control unit with the potentiometer

table 16

Technical data of the S-KD control unit

The control unit enables an easy startup of the pump with:

−

the connection board for 10-pole plug of the motor cable

−

the possibility to connect the voltage supply to the screw clamps

−

the analog voltage signal to the screw clamps for speed set

Startup of the micro annular gear pump

external voltage
24 VDC / 2 A

pump

adapter board

figure 24

Connection of the micro annular gear pump mzr-2521 and mzr-2921 to the S-KD control unit

Summary of Contents for mzr-2521





























































































Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands

HNP Mikrosysteme mzr-2521, Operating Manual

Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands