HNP Mikrosysteme mzr-2521 Operating Manual Download Page 15

Page: 15 / 92

2 Safety instructions

Operating manual mzr-2521 and mzr-2921

Last update: June 2019

Technical data subject to change without prior notice!

2.4

Safety instructions for the operator

The surface temperature of the motor under full load may exceed 60°C. If

needed, this surface should be protected on site against contact in order to avoid

skin burns.

The drive should be protected against dust, water vapor condensation, humidity,

splash water, aggressive gases and liquids. Please provide for an adequate air

ventilation and thus cooling of the motor.

The micro annular gear pumps mzr-2521 and mzr-2921 must not be used in

areas exposed to explosion risks or in proximity of inflammable gases and vapors.

Possible leaks of dangerous liquids (for example from the shaft sealing) should be

guided away in a way not to represent any danger for the personnel and the

environment. The pump should be regularly checked for possible leakage. All

legal requirements in this matter should be complied with.

Take care that all risks resulting from the electric energy are excluded. For details

please refer to the instructions provided by the authorities in charge or your

power supplier.

Warning

Please insure, that the totality of the liquid supply system such as tubes, hoses,

filters etc. are free from dust or dirt particles. Impurities such as metal swarf,

plastic or glass splinters may impair or damage the pump leading to its failure.

Warning

Please, operate the pump with a filter featuring 10 µm or smaller pores. It will

protect the pump.

2.5

Safety instructions for maintenance, check and assembly of the pump

As a rule all maintenance work on the device should be performed when it is at a

standstill. The turning-off procedure described in this manual must be followed.

Pumps delivering liquids hazardous to health must be decontaminated.

Immediately after the work had been completed all safety equipment and

protection measures should be applied.

Before starting the operation, please take notice of the instructions listed in the

chapter 7.

Warning

Should a malfunction of the mzr-pump occur, do not dismantle the pump on

your own but contact one of HNP Mikrosysteme service staff for professional

assistance.

2.6

Unauthorized pump conversions and spare part manufacture

Conversions or modification to the device are only permitted with prior consent

of the manufacturer. Original spare parts and accessories authorized by the

manufacturer ensure safety. The use of other parts will annul the liability of the

pump manufacturer for any resulting consequences.

Summary of Contents for mzr-2521





























































































Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands

HNP Mikrosysteme mzr-2521, Operating Manual

Search results

Summary of Contents for mzr-2521

Reviews:

Related manuals for mzr-2521

Brands by name

Popular brands