manualshive.com logo in svg

Hitachi EP-L110E, Instruction Manual

Share
Download
Hitachi EP-L110E Instruction Manual Download Page 47

E-47

Symptoms

Check

Solution

The water is 
leaking

 Is the water tank correctly installed in the unit?

Install the water tank correctly in the unit.

 

(P.E-16, E-17)

 Is the tank cover securely attached?

Attach the tank cover securely.

 

(P.E-16)

 Is the humidifying fi lter securely installed in the unit?

Securely install the humidifying fi lter in
the unit.  

 

(P.E-32)

 Was the unit tilted or carried while there was still 

water inside?

Place the unit on even ground, and do not carry the unit
while there is still water inside.
Also, when transferring the unit on casters, there 
is a risk of spilling the water, therefore, transfer 
the unit slowly across a fl at surface.

 Are there any cracks in the water tank or tank cover?

Immediately stop using the unit, go to your shop 
dealer and request repairs.

 Is water leaking from the tank?

Immediately stop using the unit, go to your shop 
dealer and request repairs.

The Filter Clean-
ing indicator 
does not turn off

 If you unplug the power cord, does the Filter Clean-

ing indicator reset?

Once you unplug the power cord, the humidifying 
operation time will reset and the indicator will turn 
off.

 

(P.E-30)

The touch op-
eration panel dis-
play disappeared

 Did you set the touch operation panel display to be 

hidden?

Hold display switch button for 3 seconds and 
switch the display settings.  

 

(P.E-20)

It is hard to
remove
the smell
or
the unit has a 
smell

 Is the pre-fi lter too dirty?

Refer to “Pre-filter” in “Cleaning” when cleaning 
the pre-fi lter.

 

(P.E-40)

 Is the fi lter dirty?

Or is it time to replace the fi lter?

Refer to “Replacing the Filter Assembly / Deodor-
izing Filter” when replacing the fi lter.
Depending on the location or usage, the replace-
ment interval may be shorter.  

 

(P.E-43, E-44)

 Is the humidifying fi lter dirty?

Or is it time to replace the humidifying fi lter?

Refer to “When the Filter Cleaning Indicator 
Comes On” in “Cleaning” when cleaning the hu-
midifying fi lter.  

 

(P.E-30 - E-33)

The airfl ow rate 
switched in the 
middle of operation

 Is it set in “Auto” airfl ow rate, or “Pollen” or “Eco 

Saving Operation” quick cycles?

Switch airfl ow rate and quick cycle.

 

(P.E-21 - E-23)

 Are the rear panel, fi lters, and humidifying fi lter 

correctly set?

Set them correctly.

The Empty Dust 
indicator does 
not turn off

 If you unplug the power cord, does the Empty 

Dust indicator reset?

Once you unplug the power cord, the operation 
time will be reset and the indicator will go off. 

 

(P.E-36, E-37)

 T

roubleshooting Guide

EP-L110E_EN.indd   47

EP-L110E_EN.indd   47

2/7/2018   10:55:13 AM

2/7/2018   10:55:13 AM

Summary of Contents for EP-L110E





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands