manualshive.com logo in svg

Hitachi EP-L110E, Instruction Manual

Share
Download
Hitachi EP-L110E Instruction Manual Download Page 15

E-15

Install the pre-filter to the unit

Attach the rear panel to the unit

Filter assembly

5

6

4

Securely plug the tabs of the pre-filter to the matching holes in the unit.

Slide the switch downwards (2 locations) to lock.

Gently pull the pre-filter to make sure it is not out of place.

Deodorizing filter

CAUTION

Install the filter assembly to the unit

 Do not put excessive force and deform 

the filter assembly.  
If the filter assembly is deformed, it will 
not be detected by the unit.
 “        ” will be displayed on the 
temperature / humidity monitor, and the 
unit will not be able to operate. 

    

 (P.E-45)

 When the rear panel cannot be attached properly or "      " is displayed 

on the temperature / humidity monitor after the panel is attached

Plug the tabs (2 locations) of the 
upper part of the rear panel to 
the matching holes in the unit.

Gently push the bottom sides of 
the panel one after another, and 
close it securely until it clicks.

The drive connection part does not 

properly engage in some cases. 

In this case, remove the rear panel, slowly 

turn the drive connection part on the rear 

panel about 45 degrees to the left or right, 

and then attach the panel.

Set the filter assembly so that you can see the label

Pre-filter

Switch

Slide the switch downward.

Plug the tabs of the pre-filter

Tab

Insertion hole

Insert to the hole

Note

Rear panel

Drive connection part

 Pr
eparations for Operation

Continued on next page

EP-L110E_EN.indd   15

EP-L110E_EN.indd   15

2/7/2018   10:54:56 AM

2/7/2018   10:54:56 AM

Summary of Contents for EP-L110E





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands