6
English
Table 2
Indications of the pilot lamp
The
pilot lamp
lights or
blinks in
red.
Before
charging
Blinks
Lights for 0.5 seconds. Does not light for 0.5
seconds. (o
ff
for 0.5 seconds)
While
charging
Lights
Lights continuously
Charging
complete
Blinks
Lights for 0.5 seconds. Does not light for 0.5
seconds. (o
ff
for 0.5 seconds)
Charging
impossible Flickers
Lights for 0.1 seconds. Does not light for 0.1
seconds. (o
ff
for 0.1 seconds)
Malfunction in the back pack
power supply or the charger
The
pilot lamp
lights in
green.
Overheat
standby
Lights
Lights continuously
Back pack power supply
overheated.
Unable to charge.
(Charging will commence when
back pack power supply cools)
NOTE:
The cooling fan does not rotate while the back pack power supply is charging.
If the adapter of back pack power supply is reinserted
within 3 seconds, the back pack power supply may not
be properly charged.
MOUNTING AND OPERATION
Action
Figure
Page
Pull-out direction of the output
cord from the high-capacity
power supply
1
151
Attaching the carrier
2
151
Attaching the carrier strap
3
151
Storing the switch panel
4
151
Connecting power supply
connectors and adapter
connectors
5
151
Examples showing how to use
the arm band
6
151
Main switch
7
152
Power switch
8
152
Charging the high-capacity
power supply
9
152
Using the power supply to power
cordless power tools
10
152
Warning lamp indications
11
152
Remaining capacity indications
12
152
Using the power supply to power
USB devices
13
153
Preventing short-circuits when
the power supply is not in use
14
153
Selecting accessories
―
154
●
Regarding the temperature and charging time of the
back pack power supply
The temperatures and charging time will become as
shown in
Table 3
.
Table 3
Charger
Battery
UC36YRSL
Charging voltage
V
36 V
Type of battery
Li-ion
Temperatures at which the back pack
power supply can be recharged
0
o
C – 50
o
C
Charging time for battery capacity,
approx.(At 20
o
C)
21 Ah
h.
10
NOTE
The recharging time may vary according to the ambient
temperature and power source voltage.
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger
fi
rmly and pull out the adaptor of
back pack power supply.
NOTE
Be sure to pull out the adaptor of back pack power
supply from the charger after use, and then keep it.
When the back pack power supply is not in use, switch
it OFF.
CAUTION
○
If the back pack power supply are charged while it is
heated because it has been left for a long time in a
location subject to direct sunlight or because the back
pack power supply have just been used, the pilot lamp
of the charger lights up green. In such a case,
fi
rst let
the back pack power supply cool, then start charging.
○
When the pilot lamp
fl
ickers in red (at 0.2-seconds
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the back pack power supply
or charger is malfunctioning. Take it to your authorized
Service Center.
○
Since the built-in microcomputer takes about 3
seconds to con
fi
rm that the back pack power supply
being charged with UC36YRSL is taken out, wait for a
minimum of 3 seconds before reinserting it to continue
charging.
000Book̲BL36200.indb 6
000Book̲BL36200.indb 6
2014/09/10 10:14:53
2014/09/10 10:14:53
