manualshive.com logo in svg

Hill-Rom WatchCare Series, User And Service Manual, Page: 6 / 74

Share
Download
Hill-Rom WatchCare Series User And Service Manual Download Page 6

WatchCare™ Incontinence Management System User and Service Manual (196414 REV 2) 
iv

Table of Contents

Foot-End Cover With Holes  . . . . . . . . . . . . . . . . . . . . . . . . .   36

Foot-End Cover without Holes  . . . . . . . . . . . . . . . . . . . . . .   37

Final Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   39

Antenna Assembly Replacement  . . . . . . . . . . . . . . . . . . . . . . . . . . . .   42

Graphic Replacement for the Head, Seat, and Thigh Sections, 
and Deck Filler—Progressa® Bed. . . . . . . . . . . . . . . . . . . . . . . . . . . . .   45

Equipment Call Cable Replacement . . . . . . . . . . . . . . . . . . . . . . . . . .   48

Label Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   52

WatchCare™ System Function Check . . . . . . . . . . . . . . . . . . . . . . . . .   53

Specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   54

Electromagnetic Emissions Guidance . . . . . . . . . . . . . . . . . . . . . . . .   56

Electromagnetic Immunity Guidance  . . . . . . . . . . . . . . . . . . . . . . . .   57

Wireless Connectivity Specifications . . . . . . . . . . . . . . . . . . . . . . . . .   60

Standards  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   60

Encryption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   60

Extensible Authentication Protocol Types (EAP Types)  . . .   61

Regulatory Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   61

USA—Federal Communications Commission (FCC) Radiation 
Exposure Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   62

Interference Statement for FCC. . . . . . . . . . . . . . . . . . . . . . . . . .   62

Wireless System Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . .   63

RFID Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   65

FCC ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   65

FCC ID WiFi and Bluetooth®  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   65

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   66

DRAFT 26-FEB-2019

Summary of Contents for WatchCare Series











































































Reviews:

No comments