manualshive.com logo in svg

Hill-Rom WatchCare Series, User And Service Manual, Page: 68 / 74

Share
Download
Hill-Rom WatchCare Series User And Service Manual Download Page 68

WatchCare™ Incontinence Management System User and Service Manual (196414 REV 2)
62

 

Specifications

USA—F

EDERAL

 C

OMMUNICATIONS

 C

OMMISSION

 (FCC) R

ADIATION

 

E

XPOSURE

 S

TATEMENT

CAUTION:

Caution

—The radiated output power of the WatchCare™ reader is far 

below the FCC radio frequency exposure limits. Nevertheless, the 
WatchCare™ reader must be used in such a manner that the potential for 
human contact during normal operation is minimized. To avoid the 
possibility to exceed the FCC radio frequency exposure limits, you (or any 
other person) should—

•

Progressa® and VersaCare® Beds

—Keep a distance of at least 8" 

(20 cm) from the WatchCare™ reader.

•

Keep a distance of at least 0.39" (1.0 cm) from the WatchCare™ 
antennas.

Interference Statement for FCC

This device complies with Part 15 of the FCC Rules. Operation of the 
device is subject to these two conditions: (1) the device may not cause 
harmful interference, and (2) the device must accept any interference that 
may cause unwanted operation.

This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are 
designed to supply reasonable protection against harmful interference in 
a residential installation. This equipment generates, uses, and can radiate 
radio frequency energy. If the equipment is not installed and used in 
accordance with the instructions, the equipment may cause harmful 
interference to radio communications. There is no guarantee, however, 
that such interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television 
reception (which can be determined by turning the equipment off and 
on), the user is encouraged to take one of these measures to try to correct 
the interference:

•

Move this device.

•

Increase the separation between the device and the receiver.

•

Connect the device to an outlet on a circuit difference from that 
of other electronics.

•

Consult the dealer or an experienced radio technician for help.

The WatchCare™ reader must be installed and used in strict accordance 
with the manufacturer’s instructions as described in the user 
documentation that comes with the product. Any other installation or use 

DRAFT 26-FEB-2019

Summary of Contents for WatchCare Series











































































Reviews:

No comments