manualshive.com logo in svg

Hill-Rom WatchCare Series, User And Service Manual, Page: 63 / 74

Share
Download
Hill-Rom WatchCare Series User And Service Manual Download Page 63

WatchCare™ Incontinence Management System User and Service Manual (196414 REV 2)  

57

Specifications

into service according to the EMC information supplied in the tables that 
follow.

E

LECTROMAGNETIC

 I

MMUNITY

 G

UIDANCE

 Guidance and Manufacturer's Declaration—Electromagnetic Emissions

The P006979 is intended for use in the electromagnetic environment specified 
below. The customer or the user of the model P006979 should make sure it is 
used in such an environment.

Emissions Test

Compliance

Electromagnetic Environment—
Guidance

RF emissions 
CISPR 11

Group 1

The P006979 is an intentional radiator 
of RF energy. Therefore, its RF emissions 
are low and may cause interference in 
nearby electronic equipment (see the 
tables that follow). 

RF Emissions 
CISPR 11

Class A

NOTE: The EMISSIONS characteristics of 
this equipment make it suitable for use 
in industrial areas and hospitals (CISPR 
11 class A). If it is used in a residential 
environment (for which CISPR 11 class B 
is normally required) this equipment 
might not offer adequate protection to 
radio-frequency communication ser-
vices. The user might need to take miti-
gation measures, such as relocating or 
re-orienting the equipment

.

Harmonic Emis-
sions 
IEC 61000-3-2

Not applica-
ble

Voltage Fluctua-
tions/
Flicker Emissions 
IEC 61000-3-3

Not applica-
ble

Guidance and Manufacturer's Declaration - Electromagnetic Immunity

The P006979 is intended for use in the electromagnetic environment specified 
below. The customer or the user of the P006979 should make sure it is used in 
such an environment.

Immunity Test

IEC 60601-1-2
Test Level

Compliance 
Level

Electromagnetic 
Environment—
Guidance

Electrostatic 
Discharge (ESD)
IEC 61000-4-2

± 8 kV Contact
± 2 kV, ± 4 kV, ± 
8 kV, and ± 15 
kV Air

± 8 kV Contact
± 2 kV, ± 4 kV, ± 
8 kV, and ± 15 
kV Air

Floors should be 
wood, concrete, or 
ceramic tile. If floors 
are covered with 
synthetic material, 
the relative humid-
ity should be at least 
30%.

DRAFT 26-FEB-2019

Summary of Contents for WatchCare Series











































































Reviews:

No comments