manualshive.com logo in svg

Hill-Rom WatchCare Series, User And Service Manual, Page: 5 / 74

Share
Download
Hill-Rom WatchCare Series User And Service Manual Download Page 5

WatchCare™ Incontinence Management System User and Service Manual (196414 REV 2)

 iii

Table of Contents

Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   1

Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   2

Document Symbols  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2

Product Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   2

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   4

FCC Guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   5

Quick View™ List of Features  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6

Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6

Indicator Light—Visual Identification . . . . . . . . . . . . . . . . . . . . .  8

Prepare the System for Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9

Replace the WatchCare™ smart pad . . . . . . . . . . . . . . . . . . . . . .  12

Transport The Bed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12

Cleaning and Disinfecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13

Recommendations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14

Cleaning and Disinfection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14

Prepare for Cleaning and Disinfecting. . . . . . . . . . . . . . . . . . . .  15

STEP 1: Cleaning  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16

STEP 2: Disinfection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17

Prepare for Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17

Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17

Storage and Handling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17

Expected Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18

Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  21

Expendable Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  21

Service Parts  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  21

Service Part Replacement Procedures  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  25

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  25

Reader Replacement  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27

Power Cable Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30

Indicator Light Assembly Replacement . . . . . . . . . . . . . . . . . . . . . . .  34

VersaCare® Bed  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  35

Progressa® Bed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  35

DRAFT 26-FEB-2019

Summary of Contents for WatchCare Series











































































Reviews:

No comments