Hill-Rom 20090059 Assembly Instruction Manual Download Page 7

Page: 7 / 60

www.liko.com

Golvo

™

Rear Wheel 75 mm

Bakhjul 75 mm

Assembly Instruction

Monteringsanvisning

Prod. No. 20390002

20490015

182903 Rev.1

2013-08-14

www.liko.com

Tools required:

16 mm

A&B)

Mount the new spare part. Assemble in reverse order.

NOTE

- Make sure the spare part is mounted according to the assembly instruction.

- Check all functions related to the changed spare part.

- Repairs and maintenance may only be performed by personnel authorized by Hill-Rom/Liko and using original Liko spare parts.

Contains:

Qty:

Rear wheel 75mm

20390002 Fits:

LikoLight

(up to S/N 2503101)

20490015 Fits:

Golvo 7000

(from S/N 7024206)

Golvo 7007

(from S/N 7729722)

Golvo 7000ES Classic / 7007 ES Classic

Golvo 7007 LowBase

Golvo 8000/8008

(all models)

LikoLight

(from S/N 2503102)

RollOn

Viking M

2040005

(from S/N 7102064)

Viking M

2040015

Viking S

Viking XS

5.285

Summary of Contents for 20090059





























































Search results

Summary of Contents for 20090059

Reviews:

Brands by name

Popular brands

Hill-Rom 20090059, Assembly Instruction Manual

Search results

Summary of Contents for 20090059

Reviews:

Brands by name

Popular brands