Hill-Rom 20090059 Assembly Instruction Manual Download Page 20

Page: 20 / 60

www.liko.com

Golvo

™

Friction plates 2.8-3.4 mm

Glidplattor 2.8-3.4 mm

Assembly Instruction

Monteringsanvisning

Prod. No. 20090072

3SE650254-02

2010-05-10

Fits:

Golvo 7000/7007 (all models)

Golvo 8000/8008 (all models)

www.liko.com

5.404

Contains: Qty:

Friction plate 2.8 mm

Friction plate 3.0 mm

Friction plate 3.2 mm

Friction plate 3.4 mm

Tools required

Loctite 406 (Glue)

When changing

Spare part 20090014

Actuator

, replacement of Friction plate

(pos1) may be needed. Use the same

dimension as original or as instructions

below.

(Use glue)

Alternative Friction plates.

Friction plate 3,0 mm

Friction plate 3,4 mm

When changing

Spare part 20090014 Actuator

replacement of Friction plate (pos1) may be needed.

Use the same dimension as original or as instruc-

tions below.

(Use glue)

Alternative Friction plates.

Friction plate 2.8 mm

Friction plate 3.0 mm

Friction plate 3.4 mm

Summary of Contents for 20090059





























































Search results

Summary of Contents for 20090059

Reviews:

Brands by name

Popular brands

Hill-Rom 20090059, Assembly Instruction Manual

Search results

Summary of Contents for 20090059

Reviews:

Brands by name

Popular brands