manualshive.com logo in svg

Hill-Rom 20090059, Assembly Instruction Manual

Share
Download
Hill-Rom 20090059 Assembly Instruction Manual Download Page 31

 91 

www.liko.com

  

Golvo

™

 

 

 NOTE

 

  -  Make sure the spare part is mounted according to the assembly instruction. 

  -  Check all functions related to the changed spare part. 

  -  Repairs and maintenance may only be performed by personnel authorized by HillRom/Liko and using original Liko spare parts.

www.liko.com

© Copyright Liko AB

5.514

Parking Hook for Golvo 

Parkeringskrok för Golvo

Assembly Instruction

Monteringsanvisning

Prod. No. 2006001   

3.   Replace the Roll Frame Attachment  

and mount the screws. 

 

1.  Loosen the screws (A) on the lift arm. 

Pull out the Roll Frame Attachment (B).

If pre-drilled holes are missing, follow the instructions below:

2.  Drill and thread two holes M6 under the lift arm, 

according to sketch.

      IMPORTANT!

 Remove chips from the inside of  

   the pipe. 

4.  Mount the Parking Hook with the two  

screws M6 (included) 

 

Summary of Contents for 20090059





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands