Hill-Rom 20090059 Assembly Instruction Manual Download Page 47

Page: 47 / 60

Preventative Maintenance

107

www.liko.com

7.0

Golvo

™

Instructions regarding the check points for

Golvo 7000/7007

7. Inspect gear rack for worn teeth and cracks where

stop nut contacts back surface (see arrow).

Inspect friction plates. Replace if worn or damaged.

Prod. No. 20090038 Gear rack set

20090072 Friction Plates 2,8-3,4 mm

8. Clean the friction plates/sliding surface and then

lubricate with PTFE grease. Reassemble middle

beam.

9. With middle beam at full extension, insert base motor.

Verify the stop screw is tight and the nut is in the

correct orientation. The flat of the hex must be

positioned parallel with the end of the gear rack.

10. Reassemble the mast and the middle beam to legs.

Slide middle beam inserts in until the gear rack

touches the drive shaft gear.

Note

: Do not engage gear rack!

11. To set base width start base motor while applying

inword force on both legs. After the upper and lower

gear rack engage with the base motor drive gear,

both legs will retract.

Verify that distance A & B are equal.

6. Pull out the middle beam inserts.

5b Base opening & closing linkage

Summary of Contents for 20090059





























































Search results

Summary of Contents for 20090059

Reviews:

Brands by name

Popular brands

Hill-Rom 20090059, Assembly Instruction Manual

Search results

Summary of Contents for 20090059

Reviews:

Brands by name

Popular brands