HIKVISION DS-8100HFI-ST Series Page 72 User Manual Download

Page: 72 / 199

User Manual of DS-8100HFI-ST Series DVR

5.9 Configuring HDD Group for Recording and

Capture

Purpose:

You can group the HDDs and save the record files and captured pictures in certain HDD group.

Steps:

Enter HDD setting interface.

Menu>HDD

Figure 5.35 HDD General

Select

Advanced

on the left bar.

Check whether the storage mode of the HDD is Group. If not, set it to Group. For detailed information,

please refer to

Chapter 10.4 Managing HDD Group

Select

General

in the left bar.

Click

to enter editing interface.

Configuring HDD group.

Choose a group number for the HDD group.

Click

Apply

and then in the pop-up message box, click

Yes

to save your settings.

Click

to back to the upper level menu.

Repeat the above steps to configure more HDD groups.

Choose the Channels which you want to save the record files and captured pictures in the HDD group.

Select

Advanced

on the left bar.

Summary of Contents for DS-8100HFI-ST Series








































































































































































































Search results

Summary of Contents for DS-8100HFI-ST Series

Reviews:

Related manuals for DS-8100HFI-ST Series

Brands by name

Popular brands

HIKVISION DS-8100HFI-ST Series, User Manual

Search results

Summary of Contents for DS-8100HFI-ST Series

Reviews:

Related manuals for DS-8100HFI-ST Series

Brands by name

Popular brands