HIKVISION DS-8100HFI-ST Series Page 131 User Manual Download

Page: 131 / 199

User Manual of DS-8100HFI-ST Series DVR

130

Figure 8.17 Set Arming Schedule of Video Tampering

Select

Handling

tab to set up alarm response action of video tampering alarm (please refer to

Chapter

8.6

Repeat the above steps to set up arming schedule of other days of a week. You can also use

Copy

button to copy an arming schedule to other days.

Click the

button to complete the video tampering settings of the channel.

If you want to set up video loss handling method for another channel, repeat step two and three, or just

copy the above settings to it.

Figure 8.18 Copy Settings of Video Tampering

Summary of Contents for DS-8100HFI-ST Series








































































































































































































Search results

Summary of Contents for DS-8100HFI-ST Series

Reviews:

Related manuals for DS-8100HFI-ST Series

Brands by name

Popular brands

HIKVISION DS-8100HFI-ST Series, User Manual

Search results

Summary of Contents for DS-8100HFI-ST Series

Reviews:

Related manuals for DS-8100HFI-ST Series

Brands by name

Popular brands