HIKVISION DS-8100HFI-ST Series Page 170 User Manual Download

Page: 170 / 199

User Manual of DS-8100HFI-ST Series DVR

169

10.8 Configuring HDD Error Alarms

Purpose:

You can configure the HDD error alarms when the HDD status is

Uninitialized

Abnormal

Steps:

Enter the Exception interface.

Menu > Configuration > Exceptions

Select the Exception Type to

HDD Error

from the dropdown list.

Click the checkbox(s) below to select the HDD error alarm type (s), as shown in Figure 10.23.

Note:

The alarm type can be selected to: Audio Warning, Notify Surveillance Center, Send Email and

Trigger Alarm Output. Please refer to

Chapter 8.6 Setting Alarm Response Actions

Figure 10.23 Configure HDD Error Alarm

When the Trigger Alarm Output is selected, you can also select the alarm output to be triggered from the

list below.

Click the

Apply

button to save the settings.

Summary of Contents for DS-8100HFI-ST Series








































































































































































































Search results

Summary of Contents for DS-8100HFI-ST Series

Reviews:

Related manuals for DS-8100HFI-ST Series

Brands by name

Popular brands

HIKVISION DS-8100HFI-ST Series, User Manual

Search results

Summary of Contents for DS-8100HFI-ST Series

Reviews:

Related manuals for DS-8100HFI-ST Series

Brands by name

Popular brands