manualshive.com logo in svg

HIKVISION DS-8100HFI-ST Series, User Manual, Page: 188 / 199

Share
Download
HIKVISION DS-8100HFI-ST Series User Manual Download Page 188

User Manual of DS-8100HFI-ST Series DVR 

 

187 

13.1 Configuring RS-232 Serial Port 

Purpose: 

The RS-232 port can be used in two ways: 

• 

Parameters Configuration: Connect a PC to the DVR through the PC serial port. Device parameters can be 

configured by using software such as HyperTerminal. The serial port parameters must be the same as the DVR’s 

when connecting with the PC serial port. 

• 

Transparent Channel:

 

Connect a serial device directly to the DVR. The serial device will be controlled remotely 

by the PC through the network and the protocol of the serial device. 

Steps: 

1.

 

Enter the RS-232 Settings interface.

 

Menu > Configuration > RS-232 

 

 

Figure 13.1 RS-232 Settings Interface

 

 

2.

 

Configure RS-232 parameters, including baud rate, data bit, stop bit, parity, flow control and usage. 

3.

 

Click the 

Apply

 button to save the settings. 

Summary of Contents for DS-8100HFI-ST Series








































































































































































































Reviews:

No comments