manualshive.com logo in svg

Hico Medical Systems HICO-VARIOTHERM 550, Instructions For Use Manual

Share
Download
Hico Medical Systems HICO-VARIOTHERM 550 Instructions For Use Manual Download Page 34

 

Control and operation 

HICO-VARIOTHERM 550

 

34

 

6.2.3 Function test 

After switching on the device performs a function test. During this 
test observe whether all indicating elements behave as described 
below: 

•

  a short audible alarm indicates that the unit is prepared for a 

possible power failure alarm 

The unit now checks its self-sufficient protection and 

•

  shows the result in the display (12) 

•

  the temperature displays (11) and (14) shows 

 

•

  the fault lamp (13) lights up 

•

  the audible alarm is on. 

This test takes a few seconds. 

 

 

 

If the functional tests did not complete successfully, the unit 
is no longer fail safe. 

Do not operate unit if 
►  the unit does not issue the short signal tone for the power 

failure alarm when switching on. 

►  the automatic functional test automatically switches the unit 

off because it has detected a defect in the independent 
protection device. 

►  one or more displays are defective. 
In these cases, have the unit checked by HICO customer 
service. 

 

Summary of Contents for HICO-VARIOTHERM 550










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands