Hawkeye Mfg RG1300 Installation Manual Download | Manualshive

Page: 41 / 60

background image

6

016-0171-655 Rev. E

37

CHASSIS CABLE INSTALLATION

HAWKEYE POWER CONNECTIONS (NO INJECTION)

1. Locate the three way fuse panel under the right-rear of the catwalk.
2. Place an 70 Amp AMI fuse (P/N 510-1003-048) in one of the two rear positions of the fuse panel.

FIGURE 3. Hawkeye Power Connection (No Injection)

NOTE:

If the system will include Sidekick Pro™ ICD injection, a secondary fuse panel is required. The injection

pumps and Hawkeye

®

will be powered via the secondary fuse panel. Refer to See “Sidekick Pro™ ICD

Installation” on page 43. for additional information.

3. Connect one the M8 x 1.25 output studs to the power supply.

AMI Fuse

Power

Connections

«
...
39
40
41
42
43
...
»

Summary of Contents for RG1300





























































Reviews:

No comments

Related manuals for RG1300

Brand: Canon Pages: 12

Brand: Latento Pages: 60

Brand: Easy Quick Pages: 11

Brand: Radio Shack Pages: 2

AWPH360N - PAN/TILT HEAD

Brand: Panasonic Pages: 48

Brand: Laser Pages: 8

ThermoSensor Clamp

Brand: LaserLiner Pages: 44

Brand: Walkera Pages: 24

Brand: XciteRC Pages: 52

Brand: walimex Pages: 6

Brand: walimex Pages: 10

Brand: KDS Pages: 7

Brand: SimplyHome Pages: 2

Home Power Hockey Table

Brand: Great American Recreation Pages: 10

Alpha Top Easy-Flue 500 mm

Brand: Alpha Pages: 6

Brand: Baumer Pages: 3

Brand: EEZ RV Pages: 31

Brand: Propel Trampolines Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands